اكسس بوينت للشركات والمكاتب Aruba Networks APIN0225 2 Port Wireless Ac

Aruba Networks APIN0225 2 Port Wireless Access Point AP-210 Series Specifications AP-225 and IAP-225 2.4-GHz (600 Mbps max) and 5-GHz (1.3 Gbps max) radios, each with 3×3 MIMO and three integrated omni-directional downtilt antennas AP-224 and IAP-224 2.4-GHz (600 Mbps max) and 5-GHz (1.3 Gbps max) radios, each with 3×3 MIMO and three combined, diplexed external antenna connectors Wireless Radio Specifications AP type: Indoor, dual radio, 5 GHz 802.11ac and 2.4 GHz 802.11n In addition to 802.11n data rates, the 2.4-GHz radio supports 802.11ac data rates using 256-QAM modulation. This gives TurboQAM-enabled clients a 33% boost above the maximum supported data rate. Software-configurable dual radio supports 5 GHz and 2.4 GHz 3×3 MIMO with three spatial streams and up to 1.3 Gbps wireless data rate Supported frequency band (country-specific restrictions apply): 2.4000 GHz to 2.4835 GHz 5.150 to 5.250 GHz 5.250 to 5.350 GHz 5.470 to 5.725 GHz 5.725 to 5.850 GHz Available channels: Dependent upon configured regulatory domain Dynamic frequency selection (DFS) optimizes the use of available RF spectrum Supported radio technologies: 802.11b: Direct-sequence spread-spectrum (DSSS) 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM) 802.11n/ac: 3×3 MIMO with up to three spatial streams Supported modulation types: 802.11b: BPSK, QPSK, CCK 802.11a/g/n: BPSK, QPSK, 16-QAM, 64-QAM 802.11ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM Transmit power: Configurable in increments of 0.5 dBm Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements): 2.4-GHz band: +23 dBm 5-GHz bands: +23 dBm Advanced cellular coexistence (ACC) feature to effectively deal with interference from cellular systems Maximum ratio combining (MRC) for improved receiver performance Cyclic delay diversity (CDD) for improved downlink RF performance Short guard interval for 20-MHz, 40-MHz and 80-MHz channels Space-time block coding (STBC) for increased range and improved reception Low-density parity check (LDPC) for high-efficiency error correction and increased throughput Transmit beam-forming (TxBF) for increased reliability in signal delivery Supported data rates (Mbps): 802.11b: 1, 2, 5.5, 11 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54 802.11n: 6.5 to 450 (MCS0 to MCS23) 802.11ac: 6.5 to 1,300 (MCS0 to MCS9, NSS = 1 to 3) 802.11n high-throughput (HT) support: HT 20/40 802.11ac very high throughput (VHT) support: VHT 20/40/80 802.11n/ac packet aggregation: A-MPDU, A-MSDU Antennas AP-224: Three RP-SMA connectors for external dual-band antennas AP-225: Six integrated down-tilt omni-directional antennas for 3×3 MIMO with maximum antenna gain of 3.5 dBi in 2.4 GHz and 4.5 dBi in 5 GHz. Built-in antennas are optimized for horizontal ceiling mounted orientation of AP-225. Other Interfaces Two 10/100/1000BASE-T Ethernet network interfaces (RJ-45) Auto-sensing link speed and MDI/MDX PoE-PD: 48 Vdc 802.3af PoE or 802.3at PoE+ DC power interface, accepts 1.7/4.0mm center-positive circular plug with 9.5 mm length USB 2.0 port (Type A connector) Serial console interface (RJ-45, TTL levels) Visual indicators (LEDs): Power/system status Ethernet link status (2x; ENET0, ENET1) Radio status (2x; RAD0, RAD1) Kensington security slot Reset button Power Worst-case power consumption from the AP (excluding power drawn by an attached USB device): In restricted mode (PoE): 13.5 watts In unrestricted mode (PoE): 17 watts In unrestricted mode (DC): 15.5 watts Power sources sold separately Direct DC source: 12 Vdc nominal, +/- 5% Power over Ethernet (PoE): 48 Vdc (nominal) 802.3af or 802.3at-compliant source Efficient mode PoE – power save with 802.3af PoE and limited functionality on 2.4 GHz USB port disabled Second Ethernet port disabled 2.4-GHz 802.11n radio in 1×3:1SS mode Unrestricted functionality with 802.3at PoE+ Mounting Included with AP: Mounting brackets (2) for attaching to 9/16-inch or 15/16-inch T-bar drop-tile ceiling Optional mounting kits: AP-220-MNT-C2: Aruba 220 series AP mount kit contains two ceiling-grid rail adapters for Int